7.5m Length

Compatible with F70, F100, F200, F200Pro, X700, X800, X1000

Compatible with F800PRO, Q800PRO

Connects to your vehicles fusebox. activates parking mode

Installation of the hardwiring cable to your vehicle’s fuse panel enables the built-in Parking Surveillance Mode in your THINKWARE Dash Cam, while you are away from your vehicle. All Thinkware Dashcams can then monitor your vehicles Battery and will shut down if it detects it getting low. Compatible with all THINKWARE Dash Cam models except for the M1 Mostorsport Cam or F790 Dash Cam

Full HD 1080P infrared image quality 140 degree viewing angle 0.6M Cable length Dimensions: 61mm (W) x 33mm (D) x 27mm (H)

Increase the duration of the Parking Surveillance mode of your Thinkware Dash Cam with the iVolt Mini External Battery. It allows your Thinkware dash cam to remain in Parking mode for up to 20 hours, or 16 hours with a rear cam added and even longer dependent on the camera and mode used. Compatible with all THINKWARE Dash Cam models. Please note that this requires the Hardwired version of the Dashcam

Increase the duration of the Parking Surveillance mode of your Thinkware Dash Cam with the iVolt PRO External Battery. With its 8.5 A high-speed charging, the external battery is capable of operating a dash cam for up to 27 hours on approximately 50-minute charge. Max recording time will vary by the Thinkware Dash Cam in use. Supports parallel installation of two external batteries to expand battery capacity. Compatible with all Thinkware Dash Cam models.

In some circumstances you may need to extend the Rear cable length in order to rear the optimum rear camera placement, should you need to do this Thinkware have the below the rear camera extension cables available

Designed for easy installation, the OBDII cable enables built-in Parking Surveillance Modes; Motion Detection, Impact Detection, Time Lapse Mode*, Energy Saving Mode* Compatible with all Thinkware Dash Cams, except for the F790 model. *Available on Select Dash Cams

Connects to your vehicles 12v accessory (cigarette lighter) socket for easy installation

The 12V Power Cable connects your THINKWARE Dash Cam to your vehicle’s interior Accessory power outlet Compatible with all THINKWARE Dash Cam models except for the F790 and M1.

Lens flares, light reflections, and windshield glares can significantly impact the quality of your dash cam footage. Eliminate these issues caused from moments of extreme brightness by easily installing THINKWARE’s Circular Polarizing (CPL) Filter. Simply use the guide points located on the CPL Filter to install this on any THINKWARE Dash Cam for enhanced colour clarity, and improved light exposure. Reduce glare and increase the quality of your dash cam footage today! Compatible with ALL Thinkware Dash Cams

RADAR enables extended parking mode for the U1000 and X1000. Low power consumption makes the U1000 or X1000 top choices for parking mode protection. By adding the optional RADAR sensor, parking mode can be extended even further while still capturing pre-event footage.

In some circumstances you may need to extend the Rear cable length in order to rear the optimum rear camera placement, should you need to do this Thinkware have the below the rear camera extension cables available

A steady windshield mount will eliminate vibration and ensures that your dash cam does not fall off easily and miss important details upon impact. All Thinkware Dash Cams comes with a compact 3M adhesive tape mount that keeps your dash cam in place and does not block the driver’s view of the road.

A steady windshield mount will eliminate vibration and ensures that your dash cam does not fall off easily and miss important details upon impact. All Thinkware Dash Cams comes with a compact 3M adhesive tape mount that keeps your dash cam in place and does not block the driver’s view of the road.

The Thinkware Locking Box is a compact solution for dash cam users who need to apply an extra layer of security for their T700 Series dash cams. Ideal for commercial, fleet and rental vehicles, The Secure box locks the power cable and Micro SD memory card into the unit, preventing the stored footage from being tampered. The locking box can also secure accessories such as Thinkware GPS Antenna and other secondary cameras on the T700. With Thinkwares Hard Wire Cable and proper installation, the camera can’t be turned off when the vehicles engine is running. Supplied with an adhesive pad.

If you are looking to further increase your protection, you can simply add a rear camera to most of thinkwares Front facing main units. The rear cam simply fits to your rear window and looks backwards, this plugs into the front unit via the supplied cable (please check unit specs for lead length) and then all footage is recorded on the front cameras Micro SD card.

A steady windshield mount will eliminate vibration and ensures that your dash cam does not fall off easily and miss important details upon impact. All Thinkware Dash Cams comes with a compact 3M adhesive tape mount that keeps your dash cam in place and does not block the driver’s view of the road.

Thinkware uses 3M VHB (Very High Bond) double sided tape with industrial strength. This is perfect for fitting a dashcam to a windscreen that endures extreme heat and cold environment’s

A steady windshield mount will eliminate vibration and ensures that your dash cam does not fall off easily and miss important details upon impact. All Thinkware Dash Cams comes with a compact 3M adhesive tape mount that keeps your dash cam in place and does not block the driver’s view of the road.

Thinkware uses 3M VHB (Very High Bond) double sided tape with industrial strength. This is perfect for fitting a dashcam to a windscreen that endures extreme heat and cold environment’s

Thinkware uses 3M VHB (Very High Bond) double sided tape with industrial strength. This is perfect for fitting a dashcam to a windscreen that endures extreme heat and cold environment’s